23g (Size M)
Introduction
Ultralight mittens born from surplus fabric
The UL Mittens are ultralight and easy to carry with only 19g in weight. They were born out of an idea to reuse surplus fabric from the UL All-weather Hoody.
Although they are not completely waterproof since the stitches are not seam sealed, the fabric itself is wind/waterproof and will serve you as functional rain mittens or wind-protection gloves.
*For seam sealing instructions, please refer to the Instuction section down below.
About fabric color
There may be slight variations in color by each product.
Form and function
Details
The three-dimensional design for the thumb doesn’t obstruct movement.
These compact mittens can be stashed in any pocket. At just 19g you wouldn’t hesitate to take pack them out for your next adventure.
The paper-thin UL Mittens are touchscreen compatible, allowing for easy smartphone use.
*Does not work whhen wearing liner gloves.
Quickly adjust the fitting of the wrist with the cord lock.
We made it easy for you to identify your right from your left using large letters printed on the mittens for easy identification.
Material
Pertex Shield Air
The Pertex Shield Air is a novel fabric developed by Pertex to further improve water pressure resistance, washing resistance, and overall quality from existing nanofiber membranes.
Nanofiber membranes are net-like structures made of extremely fine polyurethane (PU) fibers that are water repellent (hydrophobic). They have a sponge-like structure with many micropores, allowing the air and moisture to pass through. This air-permeability creates exceptional comfort within the clothes.
The Pertex Shield Air is much lighter than conventional nanofiber fabrics, with a weight of 50g/㎡ to 60g/㎡. For breathability and durability, our proprietary version of Shield Air has 15 denier nylon fabric (40 denier ripstop) as the outer layer and 7 denier nylon as the inner layer. This combination makes it much lighter and more breathable than other nanofiber-based, waterproof moisture-permeable fabrics.
Size guide
Product dimensions
Unit：cm
| Size | S | M |
|---|---|---|
| A | 30 | 32 |
| B | 14 | 15 |
| C | 8.5 | 9 |
| D | 15 | 16 |
Notes before use
- Not completely waterproof.
- The UL Mittens are made of our ultralight water-resistant, ultrathin, water-permeable fabric. Please handle them with care as they can be torn or ripped when rubbed against rocks or poked by branches.
- The UL Mittens are comfortable when you are on the move in a relatively warm environment. However, it is less warm than normal gloves so we strongly recommend you wear wool inner gloves to keep you warm especially when severe weather is to be expected.
- In order to maximize the moisture-permeability of the two materials, after-use care is necessary. The performances of the membrane, facing and lining can be impaired by dirt, sweat, skin oils, or other substances. Please follow the washing instructions of each product to properly wash, dry, and keep clean. The use of rainwear-specific detergent is highly recommended. The water-permeability is hindered as the water repellency is declined. The water repellency can be restored by applying the heat of a tumble dryer at low-temperature or a hairdryer. Use of a water repellent agent is recommended if it is not restored by the heat of the dryer.
- The Pertex Shield Pro uses ultralight and thin microporous material. Vaseline, insect repellent, and ethanol-containing substances such as hair creams, cosmetics, and sunscreens may stain the fabric. They may also hinder the water-permeability of the fabric.
Seam sealing
The UL Mittens are made of waterproof material. However, to make your Mittens fully waterproof, the seams must be sealed by yourself.
Instructions
We recommend Gear Aid’s “Seam Grip + WP” due to its high resistance to water and deterioration. It is a typical seam sealer glue that comes with a brush for application. Please use the brush to seam seal the Mittens is recommended. A spatula or cotton swab can be a substitute for the brush.
Stuffing the Mittens will make it easier to apply on curved areas such as the fingertips. In the photo, the body of the Mitten is stuffed with bubble wrap and the thumb with some tissue paper. It will be easier to apply the sealer when it is fully stuffed with the cord lock tightened.
The seam sealer can be applied on either the outer or inner seams, but application on the outer side is recommended for the following reasons: The inside of the mittens has a seam allowance, so if applied on the inside, it can be sticky and annoying even after the sealer is dry when in direct contact with skin. Also, application on the outer side enhances the water resistance. Apply the agent generously. Do not spread it widely. It will look nice if applied thinly along with the stitch, but it is better to apply it as thick as the width of the brush that comes with “Seam Grip + WP” for better water resistance. After application, let it dry for about 8 hours.
We recommend Gear Aid’s “Seam Grip + WP” due to its high resistance to water and deterioration. It is a typical seam sealer glue that comes with a brush for application. Please use the brush to seam seal the Mittens is recommended. A spatula or cotton swab can be a substitute for the brush.
Stuffing the Mittens will make it easier to apply on curved areas such as the fingertips. In the photo, the body of the Mitten is stuffed with bubble wrap and the thumb with some tissue paper. It will be easier to apply the sealer when it is fully stuffed with the cord lock tightened.
The seam sealer can be applied on either the outer or inner seams, but application on the outer side is recommended for the following reasons: The inside of the mittens has a seam allowance, so if applied on the inside, it can be sticky and annoying even after the sealer is dry when in direct contact with skin. Also, application on the outer side enhances the water resistance. Apply the agent generously. Do not spread it widely. It will look nice if applied thinly along with the stitch, but it is better to apply it as thick as the width of the brush that comes with “Seam Grip + WP” for better water resistance. After application, let it dry for about 8 hours.
Instructions
Care instructions
- Machine wash, gentle at 30°C.
- Use rainwear-specific detergent or a neutral detergent that does not contain bleaching, softening, or brightening agents.
- Apply detergent diluted with water and wash with a soft sponge if badly stained. Do not scrub the surface joints or the seam tape on the back.
- Occasionally tumble dry the garment at an upper limit of 60°C to restore water repellency.
- Do not bleach and do not use fabric softener.
- Iron on low. Do not steam.
- Do not dry-clean.
- Vaseline, insect repellent, and ethanol-containing substances such as hair creams, cosmetics and sunscreens may stain the fabric. They may also hinder the water-permeability of the fabric. For removal methods, please refer to the our Journal; #2 – Removing stains from rainwear.
Care instruction page
For more detailed tips on how to wash, store and restore the shrunk item, please visit our Care Insturctions.
Payment
- We only accept payment by credit card for orders from overseas.
- Bank transfer is available only to customers with a Japanese bank account.
- We accept the following credit cards: Visa, Mastercard, American Express, and JCB.
- To download your receipt, please click the link included in the dispatch notice email, which will be sent once your order has been shipped.
Delivery
- Order Confirmation will be sent after the order.
- The items will be dispatched within 5 days after the payment is confirmed.
- The dispatch notice will be sent by email as soon as the items are dispatched.
- The delivery may be delayed by unforeseeable reasons such as natural disasters and other logistics issues. We appreciate your patience and understanding.
- We cannot ship multiple orders in one package due to how our delivery system is currently set up.
- We will ship to regions in North America, Oceania, and Europe via DHL. For regions in Asia, the Middle East, Central and South America, Africa, we use EMS (International Express Mail Service) for shipping. We currently cannot ship to Russia due to Japanese postal regulations.
- Shipping fees and delivery times vary depending on the shipping destination as well as the size and weight of the items. To find out how much shipping will cost, please add all of your desired items to your cart and enter your shipping information, the exact amount will be shown.
Size exchange
Choosing the right size online can be difficult. To make your purchase easier, Yamatomichi offers a size exchange program for eligible items. To request a size exchange, please use our size exchange form here. Please review the conditions below before submitting your request.
- We only accept exchanges when the item is unused (except for fitting).
- If you would like to exchange your item for a different size, please contact us within seven days of receiving your order.
- Exchanges are available only for the same color in a different size.
- If your preferred size is out of stock, we may suggest a different color instead.
- If the product is no longer available, we may need to return the original item to you.
- All shipping costs are the responsibility of the customer.
- We will send the exchanged item after receiving payment for the return shipping cost via PayPal.
- Please note that some countries may charge customs duties depending on the value of the item.
- We are unable to advise on local customs regulations. Please contact your local customs office directly.
Repair
We accept repairs for all of our Yamatomichi products. For inquiries on repair services including patching the holes, repairing with extra components, or fixing the items damaged over time, please feel free to contact us from the “Repair” section of the SUPPORT page.